20 Liter Heavy Duty PU150 Anti Slip Floor Paint For Showrooms And Garages

Heavy Duty PU150 Anti Slip Floor Paint For Showrooms And Garages 20 liter
Description:

• Heavy Duty High Impact Floor Paint.
• Application: Airless spray, conventional spray, brush or roller

Before applying our Supercoat product, we recommend that you use our Under Guard Floor Seal.

Drying Time:

• Touch dry 5/6 hours at 20°C
• Thoroughly dry at 24 hours
• Recoat after 24 hours

Technical Data:
Volume solids 48% DFT 25 microns - theoretical spread rate 13.3 sq metres/litres

Coverage:
8 sq/metres/litre

Standard Colour Range:
An extensive choice of colours available from the RAL/B.S range.

Please note our shades / batches do vary, we would advise to calcuate your surface area accurately prior to pruchase to ensure you are ordering enough of the product. However if you do need to re-order more of the exact same product please quote our batch number which can be found on the lid of the product. Company will not be held responsible for any shade variations of the product when purchased on seperate occasions.

General Info:
SUPERCOAT PU150 entry class heavy duty domestic and industrial polyurethane resin based floor paint is a market leader in its class.

This coating is Ideal for use on concrete, stone, wood, metal surfaces but not power floated, screed or bituminous floors and will withstand most forms of traffic including plant and fork trucks. However any new concrete base / floor must be more than 16 weeks old before painting and our Underguard floor seal would be recommended prior to painting with topcoat.

Key to the success of this product is its resistance to most oils and also pressure washing even with detergents (only after suitable time to cure can these levels be reached).

Product & Application information:

FOLLOW SOLVENT BASED PRODUCT DIRECTION FOR USE LEFT SIDE ON REAR OF CAN.
Product coverage rate:10m squared per litre or 107ft squared per litre

5 litre pack size should achieve 50m squared per 5 litre can or 538ft squared (one coat)

10 litre pack size should achieve 100m squared per 10 litre can or 1,076ft squared (one coat)

20 litre pack size should achieve 200m squared per 20 litre can or 2,152ft squared (one coat)

(TwothinCoats Always Advised giving adequate dry time between coats)

Dry time of coating using standard roller in areas with minimal air moisture (lab conditions)

Touch dry @ 15'c = 10/12 hours

First coat should be left to dry for 24 hours to assure adhesion to surface leave minimum of 24 hours for after coats always leaving minimum of 48 hours before 100% use of area again

true 100% cure will only be 7 days after application of last coating

(work in a well ventilated area,using no forms of naked light/fire)

please test for damp before coating by applying a small test patch or applying a clear plastic sheet (30cmx30cm) and sealing it to the floor with a high grade tape (duck tape) with out any ways of air escaping and leave for 24 hours if there is any forms of water vapour on the sheet the are will have damp and steps will need to be taken before coatings

Mix very well before use using a drill/paddle tool

If the area you are looking to coat is virgin (never been coated) or has had contamination from oil,grease,cutting agents etc,Cleaning with correct equipment/surface preparation products will be required.

The area will then need to be coated with a heavy duty pre seal and left to dry for 24 hours (you can purchase this pre seal on the drop down menu)

Power floated/Screed areas (smooth shinny concrete) will need to be treated with a acid etch or abrade by mechanical means all product info will be displayed on the item you will take collection of

A test patch is always advised as some areas my still have contamination and this could have complications when coating

Product weight
5 litre pack size 6kg minimum
10 litre pack size 12kg minimum
20 litre pack size 23kg minimum